
Overview
Automotive grade battery tab for sensors photo chemical etching forms the thin nickel current-collector tabs and power-contact leads that carry signal and supply power between a cell and its sensor module. Rather than stamping or slitting, the tab outline is imaged from artwork onto nickel foil and the unprotected metal is dissolved chemically, so the part is produced without cutting force, heat-affected zones or tool wear. The result is a burr-free, flat tab with a clean edge that can be welded or layered against the cell terminal and the sensor contact pad without risk of a stray burr bridging the separator.
For battery and sensor designers, this route removes several limits of punched tabs. A stamped edge leaves a rolled burr and micro-cracks that can pierce the separator or raise contact resistance at the sensor terminal; fine necks and stepped contact fingers are hard to hold on a thin, springy nickel foil; and every geometry revision needs a new tool. With photo chemical etching the geometry lives in the artwork, so a revised tab width or an added contact finger is a data change, and every tab on the panel etches at the same rate, giving consistent thickness, conductivity and outline from sample to volume.
Parameter Window
- Available Materials: pure nickel foil, with SUS304 / 304L / 316L stainless foil available for alternative contact designs
- Material Thickness Range: 0.01–2.0 mm; thin nickel foil is typical for sensor power tabs and current collectors
- Tolerance: dimensional tolerance scales with material thickness and is for reference only — actual accuracy depends on the part structure, tab width and foil grade
- Minimum Feature: contact fingers, necks and weld lands are defined in the artwork rather than by tooling; fine limits are confirmed at artwork review
- Surface Options: as-etched clean nickel, plating-ready surface, deburred and protective-film packed
- Conductivity & Compliance: nickel foil keeps low contact resistance; RoHS/REACH material traceability available
Manufacturing Process / Workflow (8 Steps)
- Drawing Review — Convert the cell-to-sensor stack-up and tab drawing into vector outlines, and check contact finger width and neck size against foil thickness.
- Material Prep — Select nickel foil by conductivity and thickness, shear to panel size and inspect both faces for scratches or rolled-in marks.
- Cleaning & Lamination — Degrease and de-oxidize the foil, then hot-roll dry film on both faces so no bubble sits under a narrow contact finger.
- Double-Sided Exposure — Image the tab pattern with LDI on both faces, holding front-to-back registration for the weld land and contact fingers.
- Development — Wash away unexposed resist to open the areas to be dissolved, and rework any finger that still shows residual film.
- Controlled Etching — Spray chemistry matched to nickel; time, temperature and line speed govern etch depth and produce a burr-free edge.
- Stripping & Cleaning — Remove resist, neutralize and clean, then inspect that edges are free of burr and residue before any plating step.
- AOI / Flash Inspection — Verify outline, finger position and flatness against the approved sample by AOI and flash measurement, then pack with first-article data.
Core Advantages
- Burr-free tab edge: Chemical removal leaves no rolled edge, so the tab cannot pierce the separator or short the sensor contact.
- Flat and stress-free: No stamping force means the tab stays flat and does not spring back at the weld land.
- Fine contacts without tooling: Contact fingers and necks are artwork-defined, so design revisions need no new punch.
- Consistent conductivity: Every tab on the panel etches at the same rate, keeping thickness and contact area uniform across the cell.
- Fast sampling: A new outline is a new data set, shortening the loop from sensor concept to first articles.
- Scale flexibility: The same route supports prototype quantities and volume runs, with traceability from foil lot to packed tab.
Typical Applications
- Sensor power tabs: Thin nickel tabs that feed supply power from the cell to the sensor module.
- Signal contact fingers: Etched nickel fingers for low-resistance contact at the sensor terminal.
- Current collector tabs: Nickel foil collectors for small cells and sensor backup batteries.
- Weld lands and leads: Flat, burr-free lands for spot welding to the cell terminal.
- Prototype sensor tabs: Small-batch tabs for stack-up and contact-resistance trials before tooling.
- Battery pack interconnects: Related etched nickel strips used where a clean, flat conductor is required.
Design Notes & Process Considerations
- Stack-up callout: State the tab thickness, the weld land area and the required contact resistance together with any stack-up tolerance.
- Finger and neck layout: Round internal corners and avoid isolated narrow fingers that can distort during etching.
- Burr-free requirement: Specify a burr-free edge where the tab faces the separator, as a functional requirement.
- Flatness requirement: Call out flatness on the contact face rather than only the outer outline.
- Surface finish: Choose as-etched, plating-ready or film-packed finish according to the cell environment.
- Complete drawing data: Give foil grade, thickness, finger layout and surface together to cut back-and-forth confirmation.
