High-precision metal component manufacturer

Consulting hotline

+086 0755-2708-8292 / 18938693455
Micro Precision Shim Etching for Razors
Release Date:2026-11-16

Micro Precision Shim Etching for Razors

Overview

Micro precision shim for razors photo chemical etching produces the thin flat spacers and blade-setting washers that fix gap, alignment and stack height inside a shaving cartridge or razor head. Instead of punching or grinding, the shim outline is imaged from artwork onto stainless foil and the unprotected metal is dissolved chemically, so the part is formed without cutting force, heat or tool wear. The result is a burr-free, flat spacer with a clean edge that sits consistently against the blade and the cartridge rail.

For cartridge designers, this route removes several limits of stamped shims. A punch leaves a rolled burr that can scratch the blade edge or shift the cutting gap; fine adjusters and micro slots are hard to hold on a thin springy foil; and every geometry change needs a new tool. With photo chemical etching the geometry lives in the artwork, so a revised gap or a new micro tab is a data change, and every shim on the panel etches at the same rate, giving consistent thickness and outline from sample to volume.

Parameter Window

  • Available Materials: SUS304 / 304L / 301 / 316L stainless foil, selected for spring response and corrosion resistance in wet shaving environments
  • Material Thickness Range: 0.01–2.0 mm; thin foil is typical for blade-setting spacers, thicker stock for support washers
  • Tolerance: dimensional tolerance scales with material thickness and is for reference only — actual accuracy depends on the part structure, slot width and foil grade
  • Minimum Feature: micro slots, tabs and adjustment openings are defined in the artwork rather than by tooling; fine limits are confirmed at artwork review
  • Surface Options: as-etched bright finish, cleaned and passivated, deburred and protective-film packed
  • Compliance: ISO 9001 process control, RoHS/REACH material traceability

Manufacturing Process / Workflow (8 Steps)

  1. Drawing Review — Convert the cartridge gap and stack-up drawing into vector outlines, and check slot width and tab size against foil thickness.
  2. Material Prep — Choose SUS foil by spring and corrosion needs, shear to panel size and inspect both faces for scratches or rolled-in marks.
  3. Cleaning & Lamination — Degrease and de-oxidize the foil, then hot-roll dry film on both faces so no bubble sits under a narrow slot.
  4. Double-Sided Exposure — Image the shim pattern with LDI on both faces, holding front-to-back registration for the blade-setting features.
  5. Development — Wash away unexposed resist to open the areas to be dissolved, and rework any slot that still shows residual film.
  6. Controlled Etching — Spray chemistry matched to the stainless grade; time, temperature and line speed govern etch depth and edge quality.
  7. Stripping & Cleaning — Remove resist, neutralize and passivate, then inspect that edges are free of burr and residue.
  8. AOI / Flash Inspection — Verify outline, slot position and flatness against the approved sample by AOI and flash measurement, then pack with first-article data.

Core Advantages

  1. Burr-free blade interface: Chemical removal leaves no rolled edge, so the spacer cannot scratch the blade or disturb the cutting gap.
  2. Flat and stress-free: No stamping force means the shim stays flat and does not spring back after setting.
  3. Micro features without tooling: Fine slots and adjustment tabs are artwork-defined, so design revisions need no new punch.
  4. Consistent stack height: Every shim on the panel etches at the same rate, keeping thickness and gap uniform across the cartridge.
  5. Fast sampling: A new outline is a new data set, shortening the loop from cartridge concept to first articles.
  6. Scale flexibility: The same route supports prototype quantities and volume runs, with traceability from foil lot to packed shim.

Typical Applications

  • Cartridge blade-setting spacers: Thin flat shims that set the blade-to-guard gap in a shaving cartridge.
  • Micro adjustment washers: SUS foil washers for fine stack adjustment in precision razor heads.
  • Guard-bar support plates: Etched plates that locate the guard and cap rails relative to the blade.
  • Prototype cartridge shims: Small-batch spacers for gap and comfort trials before tooling is committed.
  • Sensor and actuator spacers: Related thin shims used where a burr-free flat spacer is required.
  • Replacement cartridge components: Consistent spacers for aftermarket cartridge assemblies.

Design Notes & Process Considerations

  1. Gap callout: State the target blade gap and the shim thickness that produces it, together with any stack-up tolerance.
  2. Slot and tab layout: Round internal corners and avoid isolated narrow tabs that can distort during etching.
  3. Flatness requirement: Specify flatness on the blade-contact face rather than only the outer outline.
  4. Edge quality: Call out burr-free as a functional requirement where the shim touches the blade edge.
  5. Surface finish: Choose as-etched, passivated or film-packed finish according to the wet shaving environment.
  6. Complete drawing data: Give foil grade, thickness, gap, slot layout and surface together to cut back-and-forth confirmation.
Consult Message
TOP