
Overview
An etched support mask for an IC substrate stencil is the fine tooling that aligns an electroformed ABF build-up stencil during fine-pitch printing and plating. The stencil body itself is produced by electroforming nickel or a nickel-cobalt alloy on a mandrel, so its fine apertures grow by deposition and are never cut; photo chemical etching is used only for the companion mask, where a thin metal foil is imaged and the unprotected areas are chemically dissolved to leave precise apertures and datums. Keeping the two processes separate matters: electroforming delivers the stencil opening geometry, while chemical etching delivers the flat, clean support mask that registers and backs that stencil.
For substrate process engineers, the etched mask handles the parts of the job that change most often. As the ABF build-up layer and pad layout move, the stencil apertures are re-electroformed, but the support mask openings and fiducials can be updated simply by editing the artwork. Photo chemical etching keeps fine apertures free of burr and stress, and because every mask on the panel etches at the same rate, thickness and outline stay consistent from first article through volume build-up.
Parameter Window
- Mask Materials: SUS304 / 304L / 301 / 316L / 420J2 / 7C27MO2 stainless foil or nickel foil for the support mask; the stencil body is electroformed nickel or nickel-cobalt alloy only
- Thickness Range: etched mask and accessory parts 0.01–2.0 mm; stencil thickness is designed separately from aperture volume and fine-pitch layout
- Tolerance: etched mask tolerance scales with foil thickness and the electroformed stencil aperture tolerance depends on product structure — values are for reference only, actual accuracy depends on the specific geometry
- Minimum Feature: fine apertures, fiducials and datums are artwork-defined rather than tool-defined; minimum pitch is confirmed at artwork review
- Surface Options: as-etched bright finish, cleaned and passivated, deburred and protective-film packed
- Compliance: ISO 9001 process control, RoHS/REACH material traceability
Manufacturing Process / Workflow (8 Steps)
- Drawing Review — Convert the ABF pad layout and stencil outline into vector artwork, and check mask apertures against electroformed openings and fiducials.
- Stencil Electroforming — Deposit nickel or nickel-cobalt alloy onto a mandrel to build the substrate stencil with fine apertures, then strip and inspect.
- Material Prep — Select SUS or nickel foil for the support mask, shear to panel size and inspect both faces for scratches.
- Cleaning & Lamination — Degrease and de-oxidize, then hot-roll dry film on both faces so no bubble sits under a fine aperture.
- Double-Sided Exposure — Image the mask pattern with LDI on both faces, holding front-to-back registration for the fiducials.
- Controlled Etching — Spray chemistry matched to the foil grade; time, temperature and line speed govern etch depth and edge quality, forming the fine apertures of the support mask.
- Stripping & Cleaning — Remove resist, neutralize and passivate, then inspect that apertures are free of burr and residue.
- Fit & Inspection — Verify aperture outline and fiducial positions by AOI and flash measurement, trial-fit the mask to the electroformed stencil, and pack with first-article data.
Core Advantages
- Clear division of labour: electroforming holds the fine stencil apertures while etching forms the support mask and its datums.
- Fine apertures without tooling: mask openings are artwork-defined, so a pad-layout change needs no new die.
- Burr-free openings: chemical removal leaves no rolled edge, so the mask does not smear paste or scratch the stencil.
- Flat and stress-free: the etched mask stays flat and registers the electroformed stencil without warping it.
- Fast sampling: a revised layout is a revised data set, shortening the loop to first-article fit trials.
- Scale flexibility: the same route supports prototypes and volume runs, with traceability from foil lot to part.
Typical Applications
- ABF substrate masks: etched support masks that register electroformed build-up stencils.
- Fine-pitch apertures: etched foils that define fine openings around electroformed stencil geometry.
- Fiducial carriers: accessory masks carrying alignment marks for substrate printing.
- Build-up prototypes: small-batch etched masks for pad-layout and stack trials.
- Substrate carrier shims: related flat, burr-free foils used inside build-up carriers.
- Volume fit parts: consistent support masks for production fine-pitch lines.
Design Notes & Process Considerations
- Fiducial scheme: state how stencil apertures map to mask fiducials, together with the fit tolerance.
- Aperture layout: round internal corners and avoid isolated narrow tabs that can distort during etching.
- Flatness: call out flatness on the face that meets the electroformed stencil, not only the outline.
- Edge quality: specify burr-free as a functional requirement where the mask opening meets the paste path.
- Surface finish: choose as-etched, passivated or film-packed finish for the build-up environment.
- Complete data: give foil grade, thickness, aperture layout and surface together to cut back-and-forth confirmation.
