High-precision metal component manufacturer

Consulting hotline

+086 0755-2708-8292 / 18938693455
Electroformed Screen for Fuel Cells
Release Date:2026-11-18

Electroformed Screen for Fuel Cells

Overview

In a fuel cell stack, how the reactant arrives matters as much as how much of it arrives. A micro-perforated screen placed ahead of the membrane electrode assembly, at a manifold entrance or behind a gas diffusion layer does two jobs at the same time: it spreads flow over the active area so that no region starves and no region floods, and it holds back particles that would puncture a membrane or plug a channel. Both jobs depend on the same property of the screen - the aperture field. A field with even open area distributes evenly; a field with a few oversized apertures passes the debris it was meant to stop, and a field with a burr on the face that touches the diffusion layer leaves a point for a puncture.

Electroforming builds the screen from the aperture outward. The field is defined as resist pillars on the plating surface; nickel grows in the open area between them, closes into a continuous sheet at the target thickness, and once the resist is stripped the apertures run straight through the metal. Because the aperture is a void left by a pillar and its wall is a plated surface, the wall is smooth and can carry a taper set by the plating conditions. There is no blanking, no laser cut and no recut burr at the rim, no weave, no crossing wire, and no braze or adhesive anywhere in the flow path. Thickness is set by plating time, and thickness is what fixes the length of each aperture - and therefore the pressure drop the screen adds to the loop.

Etching supplies the locating frame and nothing else. A screen thin enough to sit in a flow channel cannot be aligned, clamped and sealed on its own, and a stack compresses everything in it, so the screen is mounted into a frame that carries the datum edges, the gasket seal land, the clamp area and the tab windows used during build. The frame is produced by photo chemical etching because it is thin, because the land that meets a gasket must be free of burr, and because the frame datums and the screen outline have to come from the same artwork. The screen body stays electroformed nickel; in the delivered set the only etched part is the frame.

Two things separate this work from a catalogue screen. The first is lot size: fuel cell screens are usually wanted in engineering quantities - tens or a few hundred per revision, with revisions that follow bench and stack test results, which means the pattern has to be reproducible at that scale rather than only at volume. The second is the medium. A fuel cell loop is not a neutral place: coolant chemistry, humidification, pH and temperature all act on the metal, and whether nickel is the right choice has to be settled against the actual loop rather than assumed. Both questions are answered the same way - a defined pattern, a logged bath, coupons measured per lot, and an alloy agreed at drawing review.

Parameter Window

  • Material: electroformed nickel, or nickel-cobalt alloy where a stronger sheet is needed. The screen is a single deposited metal with no coating to break down at an aperture rim. The locating frame is nickel or SUS304/316L sheet.
  • Gauge: 0.03 mm to 2.0 mm across the family. Fuel cell screens sit at the thin end; the frame is the thicker member, agreed at review.
  • Aperture and open area: round, square or slot apertures from the resist pattern; open area, land width and taper follow the plating conditions agreed for the part.
  • Tolerance: quoted against the drawing, with the achievable figure depending on product structure - aperture size, pitch, sheet thickness and open area all move it, so each part is confirmed at review.
  • Surface: matte or semi-bright as agreed, specified per face. The face that touches a diffusion layer and the face that sees the manifold are not the same requirement.
  • Traceability: lot code etched into the locating frame, not the screen; coupon data and bath records filed with each lot.

Manufacturing Process / Workflow (8 Steps)

  1. Drawing review. Aperture field, open area, frame datum scheme, seal land and the medium the screen will see are reviewed together; lands too narrow to plate closed are flagged here.
  2. Pattern generation. The aperture field is written into photoresist as standing pillars on the plating surface, so aperture position, shape and taper are fixed by artwork rather than by a beam path.
  3. Electrolyte preparation. Nickel sulfamate composition, pH, temperature, filtration and agitation are checked and recorded before the panel goes into the tank.
  4. Electroforming. Current density and plating time are set against the thickness target, and deposit thickness is measured on the panel as the run proceeds.
  5. Resist removal and separation. Resist is dissolved out of the apertures, the sheet is taken off the plating surface, rinsed, dried and trimmed to the frame outline.
  6. Frame etching. The locating frame is made by photo chemical etching on a separate line: datum edges, seal land, clamp area and tab windows formed in one pass from the same artwork family as the screen outline.
  7. Assembly and flow check. Screen and frame are registered on the datum edges and bonded; the set is checked for flatness, aperture field alignment, seal integrity and, where a reference is given, pressure drop at a stated flow.
  8. Inspection and packing. Aperture coupons, thickness, open area, appearance and flatness are checked against the drawing, and parts are tray-packed so a thin screen is never stacked under load.

Core Advantages

  1. An even field, corner to corner. Every aperture comes from the same resist pattern, so open area at the edge of the panel matches the centre and the reactant sees the same resistance wherever it enters.
  2. A wall that is grown, not cut. No shear lip and no recut burr on either face, so a screen that sits against a diffusion layer offers no point for a puncture and sheds no metal into the loop.
  3. Straight-through apertures in a flat sheet. No weave, no crimp and no double thickness at an intersection, so pressure drop follows aperture length and open area rather than the geometry of a weave.
  4. Aperture length set by plating time. Thickness is a process setting, so the flow resistance of the screen can be held from lot to lot instead of drifting with stock tolerance.
  5. One metal in the flow path. The screen is nickel through its section, with no coating to break down and no dissimilar joint to set up a couple; the alloy is chosen against the medium rather than assumed.
  6. The frame takes the stack compression. A thin screen cannot carry clamp load on its own, so the etched frame takes the compression, holds the seal land flat and keeps the aperture field in register with the manifold.

Typical Applications

  • Reactant distribution screens ahead of the membrane electrode assembly
  • Manifold inlet guards that keep debris out of the flow field
  • Coolant loop screens for particulate retention
  • Humidifier support screens and flow conditioning layers
  • Backing screens behind gas diffusion media
  • Etched locating frames, seal rings and clamp plates for screen sets

Design Notes & Process Considerations

  1. Name the medium before the alloy. Coolant chemistry, humidity, pH and operating temperature decide whether nickel or nickel-cobalt suits the loop; a drawing that omits them leaves the choice to guesswork.
  2. State the flow requirement as a pressure drop at a stated flow, with the test method. Open area alone does not describe what the stack will feel.
  3. Keep the land wide enough to plate closed. Very narrow lands plate thin at the top and can leave pinholes between apertures that behave like oversized holes.
  4. State the compression the frame has to take. Stack clamp load passes through the frame, and a land sized for handling rather than for compression will not stay flat in service.
  5. Treat the seal land as a flatness item. A land that is not flat will not compress a gasket evenly, and a leak path around a screen looks exactly like a screen that passes particles.
  6. Do not use hardness as an acceptance item. What this process holds is aperture geometry, sheet thickness, open area, surface condition and flatness; a hardness figure on the drawing cannot be held.
Consult Message
TOP