
Overview
A wearable nozzle plate is a small part with a disproportionate job. In a vibrating mesh nebulizer, or in a patch that delivers a drug as an aerosol, the plate sits against a piezo element and the aperture field decides how the liquid breaks up. Droplet size, output rate and the share of the dose that actually leaves the device all trace back to the aperture: its diameter, its taper, the condition of its wall, and whether every aperture in the field matches its neighbours. Flatness matters for a different reason. The plate is coupled to the actuator across its whole face, so a plate that is not flat loads the piezo unevenly; one zone mists hard while the far zone starves, and the dose then depends on how the device happens to be held.
Electroforming builds the plate by deposition rather than by cutting. The aperture field is defined in photoresist on a polished plating surface, and nickel is grown from a sulfamate electrolyte into the open pattern until the plate reaches its thickness. The aperture is the shape the resist leaves behind and the wall is a plated surface, so the hole can be built with a taper - wider at the inlet, narrower at the exit - which is where a vibrating mesh gets its droplet size and its back-pressure behaviour. Nothing is sheared, so there is no exit lip and no recut burr, and every aperture in the field comes from one pattern, so uniformity is built in rather than sorted out at inspection.
Etching has a narrow, supporting role on this part: the carrier ring. A plate thin enough to vibrate efficiently is too thin to be picked up, oriented and bonded on its own. The ring is a thin sheet part, etched with datum edges, tab windows, clearance cut-outs and bonding lands, and the plate is registered against it through handling, cleaning, packing and assembly. It is etched because it is thin, because an edge next to a fluid path must be free of burr, and because the ring datums and the plate outline have to come from the same artwork family. The plate itself is never etched. It is electroformed nickel, and the carrier ring is the only etched part in the set.
"Medical grade" here is a specification conversation, not a stamp on the box. What the process can actually supply is a single deposited metal with no coating to flake, lot traceability, material certificates, a controlled cleaning route, and inspection records for the items named on the drawing. Those are the things a device maker audits, and each is agreed at drawing review rather than assumed from a word.
Parameter Window
- Material: electroformed nickel, or nickel-cobalt alloy where a stronger thin plate is needed. The plate is one deposited metal with no coating to flake. The carrier ring is nickel or SUS304/316L sheet.
- Gauge: 0.03 mm to 2.0 mm across the family. Nozzle plates sit at the thin end; the carrier ring is usually a little thicker, agreed at drawing review.
- Aperture geometry: round, tapered or stepped apertures are defined by the pattern; inlet-to-exit ratio and wall taper follow the plating conditions agreed for the part.
- Tolerance: quoted against the drawing, with the achievable figure depending on product structure - aperture size, pitch, plate thickness and field density all move it, so each part is confirmed at review.
- Surface: matte or semi-bright as agreed. The liquid-side face and the mist-side face are specified separately, because they are asked to do different things.
- Traceability: the lot code is etched into the carrier ring, not the plate. A plate at the thin end has no room for a legible mark, and a mark in the aperture field would change the mist.
Manufacturing Process / Workflow (8 Steps)
- Drawing review. Engineers read the aperture field, the taper direction, the thickness target and the carrier datum together, and flag any land too narrow to plate cleanly.
- Pattern generation. The aperture field is written into photoresist on the plating surface, so aperture position, shape and taper direction are fixed by artwork rather than by a machine stroke.
- Electrolyte preparation. Nickel sulfamate composition, pH, temperature, filtration and agitation are checked and recorded before the panel goes in.
- Electroforming. Current density and plating time are set to the thickness target, and deposit thickness is checked on the panel as the run proceeds.
- Release and trimming. The plate is released from the plating surface, rinsed, dried and trimmed to the outline that matches the carrier ring.
- Carrier ring etching. The ring is produced by photo chemical etching on a separate line: datum edges, tab windows and bonding lands are formed in one pass from the same artwork family as the plate outline.
- Registration and joining. Plate and ring are registered on the datum edges, joined at the bonding lands, and the assembly is checked for flatness and aperture field alignment.
- Inspection and packing. Aperture size, plate thickness, appearance and flatness are checked against the drawing; parts are tray-packed so the thin plate is never stacked under load.
Core Advantages
- One pattern, one aperture size. The whole field comes from a single resist pattern, so apertures at the corner of the panel match those at the centre and the device does not mist coarse at one edge.
- A wall that is grown, not cut. There is no shear lip, no recast layer and no burr on either face, which tightens the droplet size distribution and keeps the exit clean.
- Thickness set by process, not by stock. Plating time and current set the plate thickness, so a thin plate is produced thin instead of being ground down from thicker stock.
- Flatness formed during deposition. The plate grows on a flat plating surface, so it comes off with little waviness and couples to the actuator without high spots.
- The ring carries the handling. A plate thin enough to vibrate cannot be fed into an assembly line on its own; the etched ring supplies the datums, the tab windows and the stiffness.
- Single metal, no coating. The plate is nickel through its section, so no plated layer can lift at an aperture rim and no dissimilar interface is left to corrode in the fluid path.
Typical Applications
- Aperture plates for vibrating mesh nebulizers
- Mist plates for wearable drug delivery patches
- Nozzle plates for smart inhalers and adherence-tracked devices
- Aperture plates for fragrance and skincare mist devices
- Plates for humidifier and aroma diffuser elements
- Etched carrier rings and handling frames for plate sets
Design Notes & Process Considerations
- Decide the droplet target before fixing the aperture and its taper. Droplet size, flow rate and back pressure form a triangle; moving one corner moves the other two.
- Keep the land between apertures wide enough to plate. Very narrow lands plate thin at the top and may close up; agree the minimum width with engineering rather than taking it from an old drawing.
- Specify thickness as a range with a measuring position. Deposit thickness varies slightly across a panel, so name the zone that matters and the method used to check it.
- Name both faces. The liquid side and the mist side carry different roughness requirements, and a drawing that says only "smooth" leaves the inspector to guess which side was meant.
- Do not use hardness as an acceptance item. What the process controls is plate thickness, aperture geometry, surface condition and flatness; a hardness figure on the drawing cannot be held.
- Design the carrier datum before the plate outline. The plate registers to the ring and the ring registers to the actuator, so the datum scheme decides how much aperture tolerance is left for the mist.
